.281 7.14 1.125 28.58 do not scale from this print no of positions -02 thru -36 (see note 8) polarization option -xx: position to be polarized (use pk-06-n, see fig 7, sht 2 for polarization positions) (not available for -be option) tail specification -sv: single vertical (see fig 1) (use ssm-xx-s) -sh: single horizontal (see fig 3, sht 2) (use ssm-xx-sh) -dh: double horizontal (see fig 4, sht 2) (use bch-xx-d) plating specification -s: 30" selective gold in contact area, matte tin on tail. -l: 10" selective gold in contact area, matte tin on tail. -t: matte tin on contact and tail. -f: 3" selective gold in contact area, matte tin on tail. -stl: 30" selective gold in contact area, tin/lead (90/10) on tail. -h: 30" selective gold in contact area, 3" selective gold on tail. -lm: 10" selective gold in contact area, matte tin on tail. -tm: matte tin on contact and tail. -fm: 3" selective gold in contact option -be: bottom entry (only available on -sv) (use ssm-xx-s-be) (see fig 2, sht 2) option -p: pick and place pad (only available on -sv, use ppp-12, see fig 6, sht 2) (see note 12) -k: polyimide film pad (see fig 5, sht 2) (use k-500-s00) (not available on -sh and -dh) mounting option -lc: locking clip (use lc-05-tm, see note 10) (for -sh and -dh use molded to position bodies) ssm-1xx-xxx-xx-xx-xx-x-xx-xx .290 ref 7.37 "a" "a" see note 9 .100 ref 2.54 (no of pos x .100[2.54]) .008[0.20] (cut tolerance, see note 11) .005[0.13] (molded body tolerance) .050 1.27 ref (no of pos x .100[2.54]) -.100[2.54] (no of pos x .100[2.54]) -.200[5.08] 2 max sway (either direction) ssm-xx-s 01 02 35 36 .18 4.6 .050 1.27 90 - 0 + 4 2 max sway (either direction) 'd' section "a"-"a" contact #1 lc-05-tm see note 3 .043 - .005 + .002 1.09 - 0.127 + 0.051 -sv in-process flush to .005 max 0.13 detail 'd' scale 8 : 1 c c fig 1 -sv: single vertical row (ssm-1xx-xxx-sv-lc shown) c c c ce ce ce option -tr: tape and reel (see fig 8, sht 3) (29 positions max) ce .281 7.14 1.125 28.58 sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [0.3] 2 .xxx: .005 [0.13] .xxxx: .0020 [0.051] material: .100[2.54] c.l. surface mount socket strip by: ssm-1xx-xxx-xx-xx-xx-x-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing kolb 09/11/1998 3 1 sheet scale: 2:1 insulator: lcp, ul 94 vo, color: black contact: phos bronze f:\dwg\misc\mktg\ssm-1xx-xxx-xx-xx-xx-x-xx-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. minimum pushout force: 1lb. 3. coplanarity to be: -dh: -36 thru -28 pos: .008[0.20] -02 thru -27 pos: .006[0.15] -sv, sh: .006[0.15]. 4. package in tubes per sht 2, table 2. all other positions bulk package. 5. maximum cut flash: .015[0.38]. 6. notch of ppp-12 to be oriented toward same end as position 1. 7. rows to be within .004[0.10] of one another. 8. -36 max position available, -50 for stock only. 9. endwall after cutting: .033[0.84].005[0.13] 10. due to the high amount of insertion force needed, the -lc option is not compatible with auto placement. samtec recommends manual placement for all assemblies with the -lc option. 11. for -sv tail style: even cuts lose 2 positions per cut; odd cuts lose 1 position per cut. 12. if polarization occurs at center position(s) of body, move pick & place pad left or right to next available position. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision ce
2 max sway (either direction) ssm-xx-s-be fig 2 -sv-be: single vertical row bottom entry (ssm-1xx-xxx-sv-be shown) (different as shown, otherwise same as fig 1) .320 ref 8.13 .020 ref 0.51 ssm-xx-sh .125 3.18 .070 1.78 "b" "b" 36 01 lc-05-tm .443 - .020 + .010 11.25 - 0.508 + 0.254 .053 ref 1.35 .015 0.38 .055 1.40 90 3 (typ) 2 max sway (either direction) section "b"-"b" contact #1 see note 3 .272 ref 6.91 bch-xx-d .225 5.72 .070 1.78 .100 2.54 "c" "c" 01 02 72 71 .055 1.40 flush to .008[0.20] max (see note 7) .430 .020 10.92 0.508 .055 ref 1.40 section "c"-"c" contact #1 contact #2 .078 1.98 .167 4.24 .064 1.63 .063 1.60 "r" "s" .010[0.25] .1378 3.500 fig 5 -k: kapton pad (ssm-110-xxx-sv-k shown) (different as shown, otherwise same as fig 1) "r" = see fig 1, sheet 1 for oal "s" = "r"/2 - .0689[1.750] 01 .295 7.49 "r" .395 10.03 ref "s" .010[0.25] fig 6 -p: pick and place pad (ssm-110-xxx-sv-p shown) -02 and -03 pos not available with polarization -04 pos - cannot offer if polarization is pos 2 or 3 -05 pos - cannot offer if polarization is pos 3 *must use tr on pos 2 & 3 (different as shown, otherwise same as fig 1) "r" = see fig 1, sheet 1 for oal "s" = if no of pos is odd: "r"/2 - .1975[5.017] if no of pos is even: "r"/2 - .2475[6.287] pos 1 see note 6 ppp-12 .050 1.27 ref .195 4.95 ref fig 7 polarization (different as shown, otherwise same as fig 1) ssm-136-xxx-sv-02 shown ce pk-06-n 36 01 02 pk-06-n 02 72 71 pk-06-n fig 3 -sh: single horizontal (ssm-136-xxx-sh-lc shown) (different as shown, otherwise same as fig 1) fig 4 -dh: double horizontal (ssm-1xx-xxx-dh-lc shown) (different as shown, otherwise same as fig 3) -dh in-process -sh in-process ssm-136-xxx-sh-02 shown ssm-136-xxx-dh-02 shown 36 02 01 01 c c c ce ce ce ce ce ce ce ce c ce ce sheet of .100[2.54] c.l. surface mount socket strip by: dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing kolb 09/11/1998 3 2 sheet scale: 2:1 revision ce f:\dwg\misc\mktg\ssm-1xx-xxx-xx-xx-xx-x-xx-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 ssm-1xx-xxx-xx-xx-xx-x-xx-xx
ssm-110-xxx-sv-tr shown user direction of unreeling pos 1 ssm-110-xxx-sh-tr shown user direction of unreeling mating side of connector contact entry side for assembly ssm-110-xxx-dh-tr shown user direction of unreeling pos 1 pos 1 core lead in side of body standoff side of body core lead in side of body standoff side of body 1st position with tube logo fig 8 -tr: tape and reel scale 1:1 ssm-1xx-xxx-dh-lc shown ssm-1xx-xxx-sh-lc shown ssm-1xx-xxx-sv-lc shown ssm-1xx-xxx-sv-lc-p shown (ssm-1xx-xxx-sv-lc-k similar) ce ce fig 9 tube views ce sheet of .100[2.54] c.l. surface mount socket strip by: dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing kolb 09/11/1998 3 3 sheet scale: 3:2 revision ce f:\dwg\misc\mktg\ssm-1xx-xxx-xx-xx-xx-x-xx-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 ssm-1xx-xxx-xx-xx-xx-x-xx-xx
|
